top of page
Franchisee Portal

Renue Systems Manual. Please Contact Us to request it.

TECHNICIAN PRODUCTIVITY GUIDELINES
PRODUCTION PER TECHNICIAN PER DAY

Notes

  1. ¹Assumes bathroom floor is not being done at the same time as any other service in the guestroom.

  2. ²Carpet Open Space includes banquet rooms, hallways and other large spaces where movement of equipment is not required.

  3. ³Tile & Grout Open Space includes the lobby and any other large spaces where movement of equipment is not required. Kitchen space takes longer.

  4. These are not requirements, but rather achievable guidelines based on our history of experienced technicians.

  5. This productivity assumes that all rooms are in a contiguous fashion and accounts for the necessary stops to fill and empty the machines.

  6. New technicians are 25-50% less productive than experienced ones.

  7. Suites and two bedroom units take approx. 33% longer to complete than a standard room.

  8. An 8 hour shift is approx. 6.5-7 hours of actual work time plus breaks and set up / tear town down times. Drive time to and from property is extra. Assumes rooms are in a consecutive order.

  9. Specialty stain removal like red wine, hair dye, etc. are not accounted for in these guidelines.

  10. Drapes does NOT include sheers. Add additional time if sheers are included at the same time as drapes.

  11. Square meters = square feet divided by 10.

PTAC Spray Wands
spray.jpg

Found a nice company that supplies some of the spray gun parts for PTAC cleaning. I especially like part #4673 as the tip rotates about 135 degrees to help get into tight places. You can order directly at http://www.oescoinc.com/spraying-systems-brass-spray-wands.html

tip.jpg

Spray gun from Jon Don but you can build the entire gun from company above at half the cost of gun below. You would just need a glove to wear when holding the handle in case it gets too hot. I find this gun below an issue sometimes when attaching the hex nipple. Threading is not perfect and if you don’t seat it just perfectly before tightening it down you can strip the threads. You will need male or female coupler depending on your setup plus the parts listed below the gun.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Spray Gun Only
Item # MP-SG2-EA
Mfr. Model # PW4000A
Rated up to 4000PSI
Rated up to 300°
Rated up to 10GPM
$108.23



https://www.jondon.com/spray-gun-only.html

Plus you need:

Part# CI-150613-EA ($3.23) – Hex Nipple 1/4” x 3/8”
 

 

 

 

 


 

 

 


Spray Body Male – CI-200993-EA ($3.67)
 

 

 

 

 




 

 

 

 

Spray Body Cap – CI-200994-EA ($2.04)
 

 

 

 

 

 

 

 

 

 




T-Jet – MP-T8004-EA ($6.40)

 

 

 

 

 

 

 

 

 

 

 

 

 

Male Coupler – MP-BH261-EA ($7.18)
 

 

 

 

 

 

 

 

 

 

 

 



Oh and don’t forget the Teflon tape around all your threads. Buy at Home Depot


 

 

 

 

 

 

 

 

 

 

 

 

 

 


For the PTAC Tray, you will order through NEWPIG.COM or (855) 493-4647 and can pay via credit card.
 

Part# PAK919 ($59.00) – Plastic Pan 28.25” x 52.25” x 5”

 

 

 

 

 

 

 

 

 

 


 

image008.jpg
image006.jpg
image012.jpg
image014.jpg
image016.jpg
image018.jpg
image024.jpg
image009.png

Learn how to Rebuild the 500 or 510 Pumptec Regulator

Posted on July 14, 2015

Learn how to Rebuild the 205 Pumptec Pump

Posted on July 15, 2015

Learn how to Install the Cam / Bearing for the 205, 207, 348, 217 Pumptec Pumps

Posted on July 15, 2015

Learn how to Rebuild the 114T Pumptec Pump

Posted on July 15, 2015

Learn how to Install Kit B for the 114 Pumptec pump

Posted on July 15, 2015

Learn how to Install the Cam / Bearing for the 112 and 114 Pumptec pumps

Posted on July 15, 2015

Learn how to install 112V Kits A and B

Posted on July 15, 2015

How-To Replace a Pumptec Pump Head – Bing Video

Posted on January 20, 2021

bottom of page